EOS R10 RF-S18-45mm F4.5-6.3 IS STM Lens Kit
- High Image Quality 24.2 megapixels APS-C sized CMOS sensor.
- DIGIC X Image Processor with a native ISO range of 100-32000 expandable to 512005.
- Dual Pixel CMOS AF II covering approximately 100% width and height2 with up to 651 zones down to EV -4.
- High speed shooting 15fps mechanical7,2, 23fps electronic shutter2,8 and RAW Burst Mode with ½ second pre-shooting.
- Subject tracking handed down from the R3 with people, animal, and vehicle detection.
- EVF approximately 2.36M dots with 100% coverage and 0.95x magnification.
Terms
The following are the terms and conditions ("Terms") for the Canon U.S.A., Inc. Auto Replenishment System (the "Service"). These Terms are between you and Canon U.S.A., Inc. ("Canon USA," "we" or "us") and govern your and our respective rights and obligations relating to the Service. Please note that your use of the Service is also governed by Canon Direct’s Terms of Use and our Privacy Statement, each of which (as changed over time) are incorporated into these Terms, and all of which govern our respective rights and obligations concerning the Service. By placing an order through, or otherwise using, the Service, you accept, and agree to be bound by, these terms, conditions, limitations and requirements. Please read these Terms carefully.
Service
We reserve the right to change the Service benefits, including discount amounts and eligibility used to determine discount amounts, at any time in our sole discretion. All such changes will apply to future orders.
When you are enrolled, the Service will automatically create a new order for Eligible Products according to the shipment schedule applicable to the frequency of the Service you have selected, until you cancel.
We may, in our sole discretion, terminate your enrollment at any time without notice. If we do so, you will only be charged for orders that have been shipped to you.
Eligible Products
The eligible products that may be ordered through the Service (the identity of which are subject to change) are set forth on the product detail page on the Canon Direct website (shop.usa.canon.com) with the option to select the Service displayed (each, an "Eligible Product"). Your participation in the Service is personal to you, and you may not assign or transfer your enrollment, or any of the benefits of the Service, to any third party without our authorization. The Service is only available to customers with shipping addresses in the 50 United States and the District of Columbia.
Offers, Orders and Returns
Discounts and any limited time promotions associated with the Service apply only to Eligible Products displaying the offer message on the product detail page on the Canon Direct website (shop.usa.canon.com). Discounts and any amounts from limited time promotions that apply to your order, if any, and which are still in effect, will be automatically deducted from your order.
Some offer details may change as you receive deliveries over time (for example, price, taxes, availability, and shipping charges). If an Eligible Product is unavailable when we plan to ship it, we will notify you that we are unable to process your order, and we will wait to process your order until the next scheduled shipping date when the Eligible Product is available. When the Eligible Product becomes available, the price will be the price when you ordered it, regardless of when it becomes available.
Returns of Eligible Products under the Service are subject to our return policy. Service enrollments are void where prohibited.
Enrollment
As part of your enrollment in the Service, you will be required to register with us so that your printer can be identified as participating in the Service. Instructions for registering your printer are contained in the introductory email sent to you after you apply for enrollment in the Service, as well as in the "My Account" section of the Canon Direct website (shop.usa.canon.com). You will be required to accept terms and conditions provided by our parent company, Canon Inc., as part of registering your printer. Canon Inc. will notify us when an ink or toner cartridge reaches a certain low ink/toner threshold, and we will fill an order for the ink or toner and ship it to you under these Terms. Information provided to us and Canon Inc. may be stored on servers outside of the United States and will be subject to our Privacy Statement. It's possible that your order for Eligible Products will not arrive prior to running out of ink or toner where your use was more than usual, particularly if such greater use occurred over 1 or 2 days.
Payment and Cancellation
The total cost charged to your payment method for each order under the Service will be the cost of the Eligible Product on the day that order is processed, less any discount offered as a percentage or dollars off at the time you registered, plus any applicable sales tax. We reserve the right to modify or cancel any discount offered at the time you registered for the Service, with notice to you, and future orders fulfilled under the Service will reflect any such change.
For each Eligible Product shipped under the Service, you authorize us to charge the payment method used when you enrolled unless otherwise directed by you. If we are unable to complete your order with the payment method you used when you enrolled, we will not fulfill the order and will notify you that your payment method needs to be updated.
Your enrollment in the Service will remain in effect until it is canceled. You can cancel or modify your enrollment at any time via the "My Account" section of the Canon Direct website (shop.usa.canon.com). If you cancel or modify your enrollment after an order has been processed, you will be charged for the order as processed. If the discount for such Eligible Product changes, the new discount will be applied to your future shipments of that Eligible Product. If, after enrollment, you are no longer in possession of your printer for any reason (e.g., due to warranty return, replacement, or exchange), the total cost for the Service will continue to be charged to your payment method until you cancel your enrollment. No refunds will be granted because of your failure to cancel your enrollment in such situation.
Your rights under these Terms will automatically terminate without notice if you fail to comply with any of its terms and conditions. In the event of such termination, we may immediately revoke your access to the Service. Our failure to insist upon or enforce your strict compliance with these Terms and will not constitute a waiver of any of our rights.
Changes to Terms
We may, in our sole discretion, change these Terms without notice to you. If any change to these Terms is found invalid, void, or for any reason unenforceable, that change is severable and does not affect the validity and enforceability of any remaining changes or conditions. YOUR CONTINUED PARTICIPATION AFTER WE CHANGE THESE TERMS CONSTITUTES YOUR ACCEPTANCE OF THE CHANGES. IF YOU DO NOT AGREE TO ANY CHANGES, YOU MUST CANCEL YOUR ENROLLMENT.
Disclaimer of Warranties and Limitation of Liability
WE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, CONCERNING THE SERVICE INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. WITHOUT LIMITING THE PRECEDING SENTENCE, UNLESS OTHERWISE REQUIRED BY APPLICABLE LAW, IN NO EVENT WILL OUR, OR OUR LICENSORS’, AGGREGATE LIABILITY UNDER THESE TERMS WITH RESPECT TO ANY CLAIM EXCEED ONE HUNDRED DOLLARS ($100.00).
Return Policy
The Canon Online Store will accept, for return or exchange, defective or unopened merchandise purchased at the Canon Online Store, subject to the exceptions and timeframe for returns listed below: All merchandise returned to the Canon Online Store must be in the original packaging with all original items (such as manuals, cables, etc.) accompanying the merchandise and a copy of the invoice/packing slip included to be eligible for return or exchange. Shipping and handling fees from your original order will not be refunded, unless the merchandise is determined by the Canon Online Store, in its sole discretion, to be defective.
See Return Policy for complete information.
Overview
The EOS R10 is perfect for content creators looking to take their creativity to the next level. Featuring a high-speed shooting 15 FPS mechanical shutter1,2, a 24.2 Megapixel CMOS (APS-C) sensor, and lightning fast autofocus, the EOS R10 camera brings some of the best features from the growing EOS R Series to a sleek, lightweight design.
Technical Specifications
Type
Digital single-lens non-reflex AF/AE camera
DIGIC X
SD card
- SD card speed class-compatible.
- Compatible with UHS-II
- Eye-Fi cards and Multimedia cards (MMC) are not supported.
Canon RF-S/RF lens group (excluding EF, EF-S and EF-M lenses)
When using Mount Adapter EF-EOS R: Canon EF or EF-S lenses (excluding EF-M lenses)
Canon RF mount
Image Sensor
CMOS sensor (compatible with Dual Pixel CMOS AF)
Approx. 24.2 megapixels
Approx. 22.3 x 14.9 mm
Approx. 3.72 µm square
Approx. 25.5 megapixels
3:2 (Horizontal: Vertical)
RGB primary color filters
Installed in front of the image sensor, non-detachable
- Self Cleaning Sensor Unit
- Removes dust adhering to the low-pass filter.
- At power off only / Enable / Disable. Performed automatically (taking about approx. 2 sec. as indicated on the screen) or manually (taking about approx. 7 sec. as indicated on the screen).
- After manually activated cleaning, the camera will automatically restart (Power OFF to ON).
- When [Multi Shot Noise Reduction], [Multiple exposures], or [HDR mode] is set, [Clean now] and [Clean manually] cannot be selected.
- Dust Delete Data acquisition and appending
- The coordinates of the dust adhering to the low-pass filter are detected by a test shot and appended to subsequent images.
- The dust coordinate data appended to the image is used by the EOS Canon Digital Professional Software to automatically erase the dust spots.
- Not available in focus bracketing, RAW burst mode, or multiple-exposure shooting.
- Manual cleaning (by hand)
Recording System
Compliant to Design rule for Camera File system 2.0 and Exif 2.31*.
*Supports time difference information.
Still: JPEG, HEIF, RAW, Dual Pixel RAW, Raw Burst, C-RAW (CR3);
Movies: ALL-I*, IPB, IPB Light
* Time-lapse movies only
(1) 1 shot only
(2) Every shot
(1) Focus Bracketing
(2) Interval Timer
(3) Bulb Timer
(4) Multi-Shot NR
3:2 Aspect Ratio
Large/HEIF/RAW: 6000 x 4000
Medium: 3984 x 2656
Small 1: 2976 x 1984
Small 2: 2400 x 1600
4:3 Aspect Ratio
Large: 5328 x 4000*
Medium: 3552 x 2664
Small 1: 2656 x 1992*
Small 2: 2112 x 1600*
RAW: 6000 x 4000
16:9 Aspect Ratio
Large: 6000 x 3368*
Medium: 3984 x 2240*
Small 1: 2976 x 1680*
Small 2: 2400 x 1344*
RAW: 6000 x 4000
1:1 Aspect Ratio
Large: 4000 x 4000
Medium: 2656 x 2656
Small 1: 1984 x 1984
Small 2: 1600 x 1600
RAW: 6000 x 4000
- Values for Recording Pixels are rounded to the nearest 100,000th.
- RAW/C-RAW images are generated at 3:2, with information added about the specified aspect ratio, and JPEG images are generated at the specified aspect ratio.
- These aspect ratios (M / S1 / S2) and pixel counts also apply to resizing.
The following file numbers can be set:
File numbering methods
- Continuous numbering
- The numbering of captured images continues even after you replace the card.
- Auto reset
- When you replace the card, the numbering will be reset to start from 0001. If the new SD card already contains images, the numbering will continue from the last recorded image in the card.
Simultaneous recording of any combination of RAW/C-RAW and JPEG/HEIF image-recording quality is supported.
Selectable between sRGB and Adobe RGB
- Auto
- Standard
- Portrait
- Landscape
- Fine Detail
- Neutral
- Faithful
- Monochrome
- User Defined 1-3
White Balance
- Auto (Ambience priority/White priority)
- Day Light
- Shade
- Cloudy1
- Tungsten light
- White fluorescent light
- Flash
- Custom2 (Custom WB)
- Color temperature
2Setting method options include [Custom White Balance] and [Shoot to set WB].
Option between ambience priority and white priority settings.
Blue/amber bias: ±9 levels
Magenta/green bias: ±9 levels
- Corrected in reference to the current WB mode's color temperature.
- Blue/amber and magenta/green shift can be set at the same time.
Viewfinder
OLED color electronic viewfinder; approx. 2.36 million dots resolution
Approx. 100% vertically and horizontally relative to the shooting image area (with image quality L, at approx. 22mm eyepoint).
Approx. 0.95x / Approx. 28 degrees (with 3:2 display, a 50mm lens at infinity, -1 m--1)
Approx. 22mm (at -1 m-1 from the eyepiece lens end)
Approx. -3.0 to + 1.0 m-1 (dpt)
Autofocus
Dual Pixel CMOS AF
AF area: Horizontal: Approx. 100% x Vertical: Approx. 100%*
Stills: Max. 651 zones (31 x 21)
Movies: Max. 527 zones (31 x 17)
EV -4 to 20 (f/1.2 lens*, center AF point, One-Shot AF, at room temperature, ISO 100)
* Except RF lenses with a Defocus Smoothing (DS) coating.
Full HD 29.97fps : EV -3.5 to 20
With an f/1.2 lens*, center AF point, One-Shot AF,at room temperature, ISO 100
* Except RF lenses with a Defocus Smoothing (DS) coating.
| AF Method |
| Whole area AF |
| Spot AF |
| 1-point AF |
| Expand AF Area (Above, below, left and right/Around) |
| Expand AF Area: Around |
| Flexible Zone AF 1,2,3 |
* Available with [AF Area] set to Whole area AF
- Applies when an RF or RF-S lens without a focus mode switch is attached.
- When lenses with a focus mode switch are attached, the setting on the lens takes precedence.
Exposure Control
Real-time metering with image sensor (384 [24x16 zone metering])
- Evaluative metering
- Partial metering (approx. 5.8% of the area at the center of the screen)
- Spot metering (approx. 2.9% of the area at the center of the screen)
- Center-weighted average metering
Still Photo Shooting : EV -2 to 20 (at room temperature, ISO 100)
Movie Recording: EV 0 to 20 (at room temperature, ISO 100)
Available ISO speeds; user-set
| Normal | ISO 100-32000 (in 1/3- or 1-stop increments) |
| Expanded | H (equivalent to ISO 51200) |
- For [Highlight tone priority], the settable ISO speed range will be ISO 200 to 32000.
- Expanded ISO cannot be set for HDR mode or during HDR PQ shooting.
User-defined ISO range - still photo shooting
| ISO Speed Range | ISO Speed |
| Minimum | L 100 - 32000 (in 1-stop increments) |
| Maximum | ISO 200 - H (51200) (in 1-stop increments) |
* Expanded ISO speeds are noted as being "equivalent" to these speeds.
User-defined Auto ISO range - still photo shooting
| Auto Range | ISO Speed |
| Minimum | ISO 100-25600 (in 1-stop increments) |
| Maximum | ISO 200-32000 (in 1-stop increments) |
ISO Auto details in still photo shooting
| Â Shooting Mode | Â No Flash | Â Using Flash | ||
| Â Variable control of maximum ISO Auto limit for E-TTL | Â Compatible lens | Â Incompatible lens | ||
| Â Creative Zone | Â P | Â ISO 100*1*2-32000*2 | Â ISO 100**1*2-6400*2 | Â ISO 100**1*2-6400*2 |
| Â TV | ||||
| Â AV | ||||
| Â M | ||||
| Â B | Â ISO 400*3 | Â ISO 400*3 | Â ISO 400*3 | |
| Â Basic Zone | Â A+ | Â ISO 100-6400 | Â ISO 100-6400 | Â ISO 100-3200 |
| Â SCN | Â Varies by shooting mode | |||
| Â Creative Filters | Â Varies by shooting mode | |||
*1 ISO 200 when [Highlight tone priority] is set to [Enable] or [Enhanced].
*2 Varies depending on [Maximum] and [Minimum] of [Auto range].
*3 If outside the setting range, changed to the value most close to ISO 400.
| Â | Photo | Movie |
|  Manual | ±3 stops in 1/3- or 1/2-stop increments | |
| AEB | ±3 stops in 1/3- or 1/2-stop increments |  |
- Auto AE lock
- The metering mode for AE lock after one-shot focus can be customized in the AE lock meter menu.
- User-applied AE lock
- In the Fv, P, Tv, Av and M modes, enabled with the AE lock button. (Press again to update.)
- Enabled in all metering modes.
Shutter
- Mechanical
- Electronic 1st-Curtain
- Electronic Shutter (1st and 2nd curtain - silent*)
* In electronic shutter shooting under conditions such as flash firing by other cameras or with fluorescent lighting or other flickering light sources, a strip of light or banding due to the brightness difference may be recorded in the image.
When [Mechanical] or [Elec. 1st- curtain] is set: 1/4000-30 sec, bulb
When [Electronic] is set: 1/4000-30 sec.
Mechanical Shutter: 1/200 sec.
Elec. 1st-curtain: 1/250 sec.
Soft-touch electromagnetic release
10-sec. delay, 2-sec. delay
| Â | Mechanical Shutter | Electronic 1st Curtain | Electronic shutter |
| Shutter-release time
lag
*Measured with shutter button pressed fully from half-pressed
position
 |
Approx. 100ms | Approx. 50 ms | Approx. 50 ms |
Based on Canon testing standards.
Image Stabilization (IS mode)
Although the camera has no in-body IS, setting to Movie digital IS during movie recording will enable digital image stabilization.
| Â Item | Â Still photo shooting | Â Movie recording |
| Â Lens IS mode | Â On / Off | Â On / Off |
| Â Movie digital IS | Â On / Off*1 | Â Off / On / Enhanced |
| Â Still photo IS | Â - | Â - |
| Â Focal length setting | Â - | Â - |
- Simultaneous use of IS mode and Movie digital IS is supported in movie recording.
*1: Functions when recording movies in still photo shooting mode.
External Speedlite
Ambience priority, standard, flash priority
Canon EX- and EL-series Speedlites
- Evaluative (Face Priority)
- Evaluative
- Average
| Â Mechanical Shutter | Â Electronic 1st curtain |
| Â 1/200-30 sec. auto | Â 1/250-30 sec. auto |
| Â 1/200-1/60 sec. auto | Â 1/250-1/60 sec. auto |
| Â 1/200 sec. (fixed) | Â 1/250 sec. (fixed) |
Provided for EX- and EL-series Speedlites
±3 stops in 1/3- or 1/2-stop increments
- E-TTL each shot
- E-TTL 1st shot
Drive System
HDR Shooting and Movie Recording
Disable / Enable
* Can be used in conjunction with Auto Lighting Optimizer.
| Recording format | Bit depth | Color sampling method | HDR specification |
| HEIF | 10 bit | YCbCr 4:2:2 | Rec. ITU-R BT.2100 (PQ) |
| Recording format | Bit depth | Color sampling method | HDR specification |
| MP4 | 10 bit | YCbCr 4:2:2 | Rec. ITU-R BT.2100 (PQ) |
Video Shooting
Click here to view full specifications PDF
Click here to view full specifications PDF
LCD Screen
TFT color, liquid-crystal monitor
3.0-inch (screen aspect ratio of 3:2)
Approx. 1.04 million dots
Approx. 100% vertically/horizontally
Manually adjustable to one of seven brightness levels
29 (English, German, French, Dutch, Danish, Portuguese, Finnish, Italian, Ukraine, Norwegian, Swedish, Spanish, Greek, Russian, Polish, Czech, Hungarian, Vietnamese, Hindi, Romanian, Turkish, Arabic, Thai, Simplified/Traditional Chinese, Korean, Malay, Indonesian, Japanese)
Playback
| Item | Still Photo | Movie |
| - | ||
| Magnify zoom display | 1.5x-10x (5 levels) | -Â |
| AF point display | Yes | - |
| Grid display | Off / 3x3 / 6x4 / 3x3+diag | -Â |
| Rating | OFF / 1 to 5
Stars Select images / Select range / All images in folder / All images on card / All found images |
|
| Image Search | Search conditions Rating / Date / Folder / Protect / Type of file (1) / Type of file (2) |
|
| Protect | Select images / Select range / All images in folder / Unprotect all images in folder / All images on card / Unprotect all images on card / All found images / Unprotect all found images | |
| Cloud RAW image processing | Supported | - |
| RAW image processing | Supported | Â |
| RAW Burst processing | Supported | Â |
| HEIF -> JPEG Conversion | Supported | - |
| Cropping | Supported | - |
The white areas with no image data will blink.
Brightness and RGB
Quick Control Function
The Quick Control screen is accessed by pressing the Quick Control button during still photo shooting.
Image Protection and Erase
- Single image (select image)
- Select range
- All images in a folder
- All images on card
- Unprotect all images on card
- All found images (only during image search)
- Unprotect all found images
Except protected images
- Select images to erase
- Select range
- All images in folder
- All images on card
- All found images
Direct Printing
Images can be sent via Wi-Fi to a PictBridge-compatible (Wireless LAN) printer and printed.
DPOF: Digital Print Order Format
Compliant to DPOF Version 1.1
Wi-Fi@
IEEE 802.11b/g/n
DS-SS modulation (IEEE 802.11b)
OFDM modulation (IEEE 802.11g/n)
Frequency: 2412 to 2462 MHz Channels: 1 to 11 channels
| Connection Method | Authentication | Encryption | |
| Encryption | Key Format and Length | ||
| Camera Access Point | WPA2/ WPA3-Personal | AES | ASCII 8 characters |
| Open | Disable | ||
| Infrastructure | Open | WEP |
|
| Disable | |||
| Shared key | WEP | Same as WEP above | |
| WPA-PSK WPA2-PSK WPA3-Personal |
TKIP AES |
1-127 characters | |
Images can be viewed, controlled, and received using a smartphone.
Remote control of the camera using a smartphone is possible depending on the Camera Connect specifications.
Images can be sent to a smartphone.
Firmware can be downloaded and saved to a card in the camera using Camera Connect.
The camera can be controlled via Wi-Fii® using EOS Utility.
Supported.
Still photos (RAW, C-RAW, HEIF, and JPEG) and movies (MP4) can be uploaded to image.canon server album.
With the image.canon server, images can be sent to social media or a photo album link can be sent (by the image.canon specifications).
Still RAW photos can be transferred to image.canon for RAW development using Deep Learning technology resulting in clearer images without losing detail through the reduction of noise, false color, moiré and jagged lines.
*This feature requires a paid subscription (service begins July 25, 2022).
Bluetooth®
Bluetooth Specification Version 4.2 compliant (Bluetooth low energy technology)
GFSK modulation
Customization
| Still photo | Movie | |
| Shutter button (half-press) | Yes | - |
| Movie shooting button | Yes | - |
| Multi-function ( |
Yes | Yes |
| ISO speed button | Yes | Yes |
| AF-ON button | Yes |  Yes |
| AE lock (<*>) button | Yes |  Yes |
| AF point button | Yes | Yes |
| DOF preview button | Yes |  Yes |
| Lens function ( |
 Yes |  Yes |
| Cross keys: Up button | Yes |  Yes |
| Cross keys: Left button |  Yes | Yes |
| Cross keys: Right button |  Yes | Yes |
| Cross keys: Down button | Â Yes | Â Yes |
| Set button | Â Yes | Â Yes |
| Multi-controller |  Yes | Yes |
| Main dial |
| Quick control dial |
| Control ring |
- Up to six top-tier menu items and Custom Functions can be registered.
- Up to five My Menu tabs can be added.
| My Menu tab overall operations |
|
| My Menu tab detailed operations |
|
Interface
Hi-Speed USB (USB 2.0) equivalent
- Terminal type: USB Type-C
- For computer communication / smartphone communication
- USB battery charging / camera power supply
HDMI micro OUT terminal Type D (Resolution switches automatically) / CEC not compatible
- Images can be displayed through the HDMI output and on screen at the same time.
- Images will not be displayed unless [NTSC] or [PAL] is properly set according to the video system of the TV set.
Provided
3.5mm diameter stereo mini jack
Not Supported
Remote Switch RS-60E3 type terminal supported
Compatible with the Wireless Remote Control BR-E1
Supported
Power Source
LP-E17
- With the USB Power Adapter PD-E1, in-camera charging is possible when camera is off.
- Automatic battery check when the power switch is turned ON.
- Displayed in 4 levels
Approx. 0.4 sec.
- Based on CIPA testing standards.
Dimensions and Weight
Approx. 4.82 x 3.46 x 3.28 in. / 122.5 x 87.8 x 83.4mm
- Based on CIPA standards.
Approx. 0.84 lbs (13.48 oz) Body Only
Approx. 0.94 lbs (15.14 oz) With battery,and memory card
Operating Environment
32-104° F / 0-+40°C
85% or less
Reviews
How is your Canon product performing for you?
EOS R10 RF-S18-45mm F4.5-6.3 IS STM Lens Kit Compatible Products
Product Disclaimer
- Continuous shooting speed may be slower due to factors such as anti-flicker shooting, aperture value, or battery life.
- Not available when Dual Pixel RAW is enabled.
- Effectiveness varies depending on the subject. In some cases, dogs, cats or birds may not be detected, while some animals other than dogs, cats or birds may be detected.
- Video may stop due to battery level, card capacity, or internal temperature.
- For still images.
- Only when a lens supporting 90% H x 100% W focusing area is attached and the camera is set to Whole-area AF, or when subjects are detected with AF area modes other than Whole-area AF. May not be possible to move AF points to the edge of the focusing area under some scene and subject conditions.
- Continuous shooting speed is slower with anti-flicker shooting.
- Only when using lenses supporting up to 23 shots/sec.
- Manual focusing is also possible with the focus mode switch to [AF] depending on the settings of lens electronic MF and electronic full-time MF.
- Panorama mode can be captured with all RF and EF lenses, the use of certain lenses can reduce subject blur during panning.