Web Content Viewer
CANON U.S.A.,Inc. MAKES NO GUARANTEES OF ANY KIND WITH REGARD TO ANY PROGRAMS, FILES, DRIVERS OR ANY OTHER MATERIALS CONTAINED ON OR DOWNLOADED FROM THIS, OR ANY OTHER, CANON SOFTWARE SITE. ALL SUCH PROGRAMS, FILES, DRIVERS AND OTHER MATERIALS ARE SUPPLIED "AS IS." CANON DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
CANON U.S.A.,Inc. SHALL NOT BE HELD LIABLE FOR ERRORS CONTAINED HEREIN, OR FOR LOST PROFITS, LOST OPPORTUNITIES, CONSEQUENTIAL OR INCIDENTAL DAMAGES INCURRED AS A RESULT OF ACTING ON INFORMATION, OR THE OPERATION OF ANY SOFTWARE, INCLUDED IN THIS SOFTWARE SITE.
I have read and understand the information above, and wish to download the designated software.
Speedlite EL-1
Contact Support
Speedlite EL-1
Compatible Cameras
Flash Coverage (Focal length; for 35mm full-frame)
14mm | Wide Panel: Manual * Not compatible with EF15mm f/2.8 Fisheye or EF8-15mm f/4L Fisheye USM shoot-ing angles of view |
24mm | Zoom • A: Auto |
28mm | |
35mm | |
50mm | |
70mm | |
80mm | |
105mm | |
135mm | |
200mm |
Guide Number
• The Guide No. is approximately 46.3 ft./14m at ISO 100.
- When the extendable wide panel is pulled out, the flash coverage is 14mm.
• The maximum Guide No. is approximately 196.9 ft./60m at ISO 100 and 200mm flash coverage.
- When the extendable wide panel is pulled out, the flash coverage is 14mm.
Maximum Energy
76Ws
Flash Modes (Exposure Control Modes)
Flash Mode | Flash ExposureCompensation | FEB | FE Lock | Wireless | |
Radio Transmission | Optical Transmission | ||||
Yes | Yes | Yes | Yes | Yes | |
Yes | Yes | ||||
Yes | Yes | ||||
Yes | Yes | Yes*² | |||
Yes | Yes | Yes | |||
Yes | Yes | Yes*⁴ | Yes |
* 1: Set automatically when the camera shooting mode is set to Basic Zone modes.
* 2: Only Group firing is available.
* 3: Can only be set when the Speedlite is used as a sender in radio transmission wireless operation.
* 4: Only groups set to E-TTL II / E-TTL autoflash.
Flash Exposure Compensation
±3 stops, in 1/3-stop or 1/2-stop*¹ increments.
* The Speedlite's flash exposure compensation takes precedence if flash exposure compensation is performed by both the Speedlite and the camera. Users who prefer to enable flash exposure compensation by the camera should set flash exposure compensation by the Speedlite to 0.
* 1: Corresponds to exposure level increments on the camera.
FEB
±3 stops, in 1/3-stop or 1/2-stop*¹ increments.
* FEB is automatically deactivated after three shots.
* Can be used with flash exposure compensation and FE lock.
* 1: Corresponds to exposure level increments on the camera.
FE Lock
Supported
FE Memory
Supported
• Stores the flash output of E-TTL II / E-TTL autoflash and automatically sets the stored output level if users switch the flash mode to manual flash.
* Flash output may vary slightly between E-TTL autoflash and manual flash.
• Colors may vary between E-TTL autoflash and manual flash under the following conditions:
* When the color temperature of the Speedlite light differs greatly from that of ambient lighting and flash exposure compensation is set toward the negative end.
* When E-TTL balance is set to (Ambience priority).
• Differences in colors between E-TTL autoflash and manual flash may be reduced by taking one of the follow steps:
* Using the provided color filter.
* Setting white balance to an option other than AWB.
0: Off | Disabled |
1: On | Enabled |
2: On / Mode ETTL - M | Enabled/ One-touch switching between E-TTL autoflash and manual flash |
Number of Flashes
Approx. 335–2,345 flashes.
* With a fully charged Battery Pack LP-EL.
* Based on Canon Testing Standards.
Recharge Time
Power Supply | Recharge Time (approx.) | Flash count (approx.) | ||||
Normal Flash | Quick Flash | |||||
Flash Power | Min. | Max. | Min. | Max. | Min. | Max. |
Speedlite EL-1 | 0.1 sec. | 0.9 sec. | 01. sec. | 0.8 sec. | 335 | 2345 |
Speedlite EL-1 + CP-E4N (AA/LR6 Alkaline batteries) | 0.1 sec. | 0.6 sec. | 01. sec. | 0.5 sec. | 560 | 3920 |
Speedlite EL-1 + CP-E4N (AA/LR6 Ni-MH batteries) | 0.1 sec. | 0.4 sec. | 01. sec. | 0.35 sec. | 680 | 4760 |
Flash Range
Effective flash range with EF 50mm f/1.4 lens at ISO 100 (Light distibution: Standard)
- Normal Flash: Approx. 1.6–85.6 ft./0.5–26.1m
- Quick Flash (Flash-ready lamp: blinking): Approx. 1.6–52.5 ft./0.5–16.0m
- High-speed Sync (at 1/250 sec. shutter speed): Approx. 1.6–45.3 ft./0.5–13.8m
AF Assist Beam
System:
Infrared AF-assist beam
Compatible AF System:-
TTL second image formation phase-difference AF
Supporting 1–191 AF points (28mm or longer focal length)
• Phase-difference AF during viewfinder shooting
Effective Range (Approx.):
At center: 2.0–32.8 ft./0.6–10.0m
At periphery: 2.0–16.4 ft./0.6–5.0m
Modeling Lamp
Brightness*¹ | Manual setting: 1 (Low) to 5 (High) *Default setting: 5 (High) |
Color temperatue*¹ | Manual setting: 1 (Orange) to 5 (White) *Default setting: 1 (Orange) |
On | Illuminated in response to the following operations • Pressing the • Pressing the shutter button halfway twice (with C.Fn-18 set to 1). |
Off | Off under the following conditions • Releasing the shutter button • Pressing the • Pressing the shutter button halfway twice (with C.Fn-18 set to 1) • Timer: 5 min. / 30 min. / Unlimited (can be changed in P.Fn-09) |
Higher LED temperatue from prolonged illumination triggers the following safety functions
Temperature in-crease | LCD Panel | Modeling Lamp Operation | |
Icon display | Illumination | ||
Level 1 | ![]() | On | Modeling lamp brightness is lowered one level, if at the maximum level |
Level 2 | ![]() | Blinking (2 Hz) | Modeling lamp is turned off |
Wireless Settings
Sender | Supported *Secondary and additional units serve as sub-senders and display a SUB SENDER icon. * Sub-senders cannot be remotely controlled by a receiver unit |
Receiver | Supported |
Communication Functions
Compliance standards | IEEE 802.15.4, ARIB STD-T66 |
Communication method | Primary modulation: OQPAK Secondary modulation: DS-SS |
Transmission frequency | 2405-2475 MHz |
Channel | Channel 1-15 Setting: Auto / Manual |
Wireless radio ID | 0000 to 9999 Setting: Manual |
Transmission range*¹*² | Approx. 98.4 ft. / 30 m |
Groups | Up to 5 groups (A-E) * Sender units are set to Group A |
Number of possible units for communication | Up to 16 units of senders and receivers in total |
Max. sender units | Up to 15 * Secondary and additional units serve as sub-senders |
Max. receiver units | Up to 15 |
* 2: Transmission range may be shorter depending on factors such as how units are arranged, the surrounding environment, and weather conditions.
Transmission Status Display
Transmission status | Display | lamp | LCD Panel | |
Sender | Receiver | |||
Connected | Yes | Yes | On (in green) | Sender, Receiver |
Not Connected | 0.1 sec. | 0.9 sec. | Off | Sender, Receiver |
Too many units/Error | 0.1-0.6 sec. | Blinking at 2 Hz (green) | Sender, Receiver | |
Sub-sender | 0.1-0.4 sec. | On (in green) | Sub Sender | |
Confirmation of linked shooting | Yes | On (in green) | RELEASE |
Wireless Firing Control
Wireless firing control via radio transmission
Flash Mode | E-TTL II / E-TTL autoflash | |
Manual flash | ||
Stroboscopic flash | ||
Group firing | E-TTL II / E-TTL autoflash | |
Manual flash | ||
Auto external flash metering |
E-TTL II / ETTL autoflash details
ALL |
A:B |
A:B+C |
Manual flash details
ALL | Flash ratio seting: 1/8192*¹*² to 1/1 |
A+B | Flash output seting: 1/8192*¹*² to 1/1 |
A+B+C | Flash output seting: 1/8192*¹*² to 1/1 |
* 1: Minimum of 1/128 for high-speed sync.
* 2: Speedlites that do not support a minimum flash output of 1/8192 use their minimum flash output instead.
Stroboscopic flash details
Flash count | 1-100 |
Flash frequency | 1-500 Hz |
ALL | Flash ratio seting: 1/8192 to 1/4 |
A+B | Flash output seting: 1/8192 to 1/4 |
A+B+C | Flash output seting: 1/8192 to 1/4 |
Group firing details
Enables separate configuration of flash firing control conditions 1-3 below for each groups (A, B, C, D, E), to combine multiple methods of flash firing control.
- E-TTL II / E-TTL autoflash
- Manual flash
- Auto external flash metering
* Flash exposure compensation ±3 stops
Test flash
Available (Sender/Receiver)
Modeling flash
Available (Sender/Receiver)
Modeling lamp
Available (Sender only)
Remote control from a receiver
Functions on sender units that can be controlled remotely from receiver units:
• Remote release
• Test flash
• Modeling flash
* Sub-senders cannot be controlled remotely
Communication functions
Compliance method | Optical pulses |
Channel | Channel 1-4 |
Transmission range (approx.) | From front of flash head • Indoors: 2.3 - 49.2 ft. / 0.7 - 15 m. • Outdoors: 2.3 - 32.8 ft. / 0.7 - 10 m. |
Reception angle (approx.) | • Horizontally: 45° • Upward: 27°, Downward: 20° |
Groups | Up to 3 groups (A-C) |
Max. sender units | Unlimited |
Max. receiver units | Unlimited |
Wireless settings
Sender | Supported |
Receiver | Supported |
Individual receiver | Supported |
Wireless
Overview of optical wireless firing control
Sender flash firing | On: Fires as Group A |
Channel 1-4 | |
OFF: Does not fire. * Firing (optical transmission) to control receivers may be visible in shots. | |
Flash mode | E-TTL II / E-TTL autoflash |
Manual flash | |
Stroboscopic flash |
E-TTL II / E-TTL autoflash details
ALL | Flash metering control of all groups (A, B, C) as if they were a single flash unit. Flash exposure compensation: ±3 stops |
A:B | Flash metering control to obtain the flash ratio set for groups A and B. • Flash ratio setting: 8:1 to 1:8 • Flash exposure compensation: ±3 stops |
A:B+C | (1) Flash metering control to obtainv the flash ratio set for groups A and B Flash ratio setting: 8:1 to 1:8 (2) Flash metering control of group C as if it were a single flash unit • Flash exposure compensation: ±3 stops The same flash exposure compensation can be set for (1) and (2) above • Flash exposure compensation: ±3 stops |
Manual Flash Details
ALL | Flash ratio seting: 1/8192*¹*² to 1/1 |
A+B | Flash ratio seting: 1/8192*¹*² to 1/1 |
A+B+C | Flash ratio seting: 1/8192*¹*² to 1/1 |
* 1: Minimum of 1/128 for high-speed sync.
* 2: Speedlites that do not support a minimum flash output of 1/8192 use their minimum flash output instead.
Stroboscopic Flash Details
Flash count | 1-100 |
Flash frequency | 1-500 Hz |
ALL | Flash ratio seting: 1/8192 to 1/4 |
A+B | Flash output seting: 1/8192 to 1/4 |
A+B+C | Flash output seting: 1/8192 to 1/4 |
Individual Receiver Details
Manual Flash | Flash output setting: 1/8192 to 1/1 |
Stroboscopic flash | •Flash output setting: 1/8192 to 1/4 •Flash count: 1-100 •Flash frequencey: 1-199Hz |
Test Flash
Available (Sender/Receiver)
Modeling Flash
Available (Sender/Receiver)
Modeling Lamp
Available (Sender only)
Linked Functions
Supports linked shooting with automatic shutter release of up to 16 cameras (sender:1, receivers:15) linked to shutter release on the sender camaera.
*Shooting is not simultaneous, because receiver cameras shoot slightly afterthe sender camera shutter release timing.
Type
Reflective memory LCD (normally black)
Size
Approx. 1.89(H) x 1.04(V) in.
Display formation
Dot-matrix display
Dot Count
Approx. 56,000 dots (320x176)
Power Source
Battery Pack LP-EL
*AA/LR6 Alkaline Batteries and Ni-MH batteries cannot be used.
Battery Charger
Battery Charger LC-E6/LC-E6E
Car Battery Charger CBC-E6
External Power Source
Supported
*Optional - Supports CP-E4N Battery Pack
PC Terminal
Supported
Modeling LampIllumination Time
Approx. 3 hr 20 min. Continously
*With P.Rn-09 set to [2], and using a fully charged Battery Pack LP-EL
Dust-and-Water Resistance
Supported
*Water-resistant performance to EOS-1D series
Dimensions (W x H x D)
Approx. 3.32 x 5.87 x 5.37
Weight (Approx.)
20.18 oz (Body Only)
24.23 oz (Body and Battery)
Light Distribution
Set in C.Fn-21
0: Standard | A light distribution setting that balances light distribution and the guide number. |
1: Guide number priority | Prioritizes illumination at the center of the screen, the periphery may be dark. |
2: Light distribution priority | Light distribution that reduces peripheral darkness. |
Custom Functions
Function | Number | Setting |
C.Fn-00: Distance indicator display | 0 | m (display in meters) |
1 | ft. (display in feet) | |
C.Fn-01: Auto power off | 0 | ON (90 sec.) |
1 | OFF | |
C.Fn-02: Modeling flash | 0 | Depth-of-field preview button |
1 | Test flash button | |
2 | DOF/Test flash button | |
3 | OFF | |
C.Fn-03: FEB auto cancel | 0 | ON |
1 | OFF | |
C.Fn-04: FEB sequence | 0 | 0 -> - -> + |
1 | _->0-> + | |
C.Fn-08: AF-assist beam firing | 0 | ON |
1 | OFF | |
C.Fn-10: Receiver auto power off timer | 0 | 60 min. |
1 | 10 min. | |
C.Fn-11: Receiver auto power off timer | 0 | Within 8 hours |
1 | Within 1 hour | |
C.Fn-12: Flash recycle with external power | 0 | External and internal pwer |
1 | External power only | |
C.Fn-13: Flash exposure compensation setting | 0 | Button and dial |
1 | Direct setting with the dial | |
C.Fn-18: Modeling lamp lit | 0 | with lamp button |
1 | Press the shutter button halfway twice *Lamp button can also be used | |
C.Fn-21: Light distribution | 0 | Standard |
1 | Guide number priority | |
2 | Even coverage | |
C.Fn-22: LCD panel illumination | 0 | Stay on for 12 sec. after operation |
1 | Disable panel illumination | |
2 | Illumination always on | |
C.Fn-23: Receiver charge confirmation | 0 | AF-assist beam blinking and flash-ready lamp |
1 | Flash-ready lamp |
Personal Functions
9 Functions
Function | Number | Setting |
P.Fn-01: AF-assist beam emission method | 0 | Infrared |
1 | Emmitting small series of flashes | |
P.Fn-02: Quick flash | 0 | ON |
1 | OFF | |
P.Fn-03: Flash firing during linked shooting | 0 | OFF |
1 | ON | |
P.Fn-04: Change settings with the direct dial operation | 0 | OFF |
1 | ON | |
P.Fn-05: FE memory | 0 | OFF |
1 | ON | |
2 | ON / MODE: ETTL<-> M | |
P.Fn-06: Beep | 0 | ON |
1 | OFF | |
P.Fn-07: Fan | 0 | ON |
1 | OFF | |
P.Fn-08: Modeling lamp (brightness, color) | Brightness: 5 levels | |
Color: 5 levels | ||
P.Fn-09: Modeling lamp (lit time) | 0 | 5 min. |
1 | 30 min. | |
2 | Unlimited |
† Prices and specifications subject to change without notice. Actual prices are determined by individual dealers and may vary.
Drivers & Downloads
Supporting Documents
Manuals
Compatible Supplies & Accessories
Canon offers a wide range of compatible supplies and accessories that can enhance your user experience with you Speedlite EL-1 that you can purchase direct. Scroll down to easily select items to add to your shopping cart for a faster, easier checkout. Visit the Canon Online Store

Battery Charger LC-E6
Battery Charger for NP-E6 Li-ion Batteries.
MSRP: 80.0

Battery Magazine CPM-E4
MSRP: 55.0

Battery Pack LP-EL
The new compact and rechargeable Li-ion Battery Pack LP-EL delivers the power and reliability needed when shooting any situation - especially weddings when a moment can be once-in-a-lifetime, so you can feel comfortable shooting over and over for extended periods of time. You can even view the remaining battery level in the top right display of the Speedlite EL-1 letting you know just how long you can go or when it's time to recharge with the LC-E6 battery charger.
MSRP: 109.99

Bounce Adapter SBA-EL
The bounce adapter SBA-EL softens flash illumination and diffuses the light, helping to keep the entire image area bright, while softening shadows, when bouncing the light off ceilings or walls. Bounce Adapter can be used with color filters.
MSRP: 29.99

Color Filter SCF-EL
The SCF color hard-type filter sets include the Color Filter SCF-ELOR1, which is effective in merging ambient incandescent light with the flash's bluish output to create a warm mood. The Color Filter SCF-ELOR2 is useful for balancing out the red fogging typical of interior lighting, for more natural, realistic light. Both filters attach and detach with ease for quick and smooth set-up.
MSRP: 29.99

Compact Battery Pack CP-E4N
The external Battery Pack improves flash recycle times significantly and increases the number of continuous flashes. Uses the CPM-E4 rapid-change Battery Magazine. The CP-E4N has quieter operation during recharging.

Off Shoe Camera Cord OC-E3
The Off-Camera Shoe Cord OC-E3 is convenient for using your flash apart from the camera. Also allows for Remote Triggering of the flash.
MSRP: 100.0
Speedlite EL-1
- Speedlite EL-1
- Soft Case (for Body/SBA-EL/SCF-EL)
- Stand
- Bounce Adapter SBA-EL
- Color Filter SCF-ELOR1 (Light Orange)
- Color Filter SCF-ELOR2 (Dark Orange)
- Battery Pack LP-EL
- Battery Charger LC-E6
